Why Learning Plumbing Basics is Crucial for Installing a Bathtub
Why Learning Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
The article author is making several good points related to Installing A Bathtub in general in this great article down the page.
Setting up a bathtub isn't precisely rocket science, but it does need strong plumbing, carpentry, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately tough job. If the old tub is conveniently available, the task can move easily; if you have to open a wall surface to get rid of the old tub and also place the brand-new tub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will need a helper to vacate the old bathtub and set in the new one. Make certain you have qualified on your own for the work as well as are comfortable attempting it. As opposed to hiring a service provider to take control of a halfway-completed task, it is better to take into consideration using one before you start. Possibilities are you might require an expert plumber to make tube connections.
This short article will certainly assist you set up a new bathtub in your washroom if you have actually currently gotten a brand-new tub and also do not require to transform the plan of your previous water system pipes.
Your devices and material checklist ought to comprise the following:
Preparing for the Setup
Firstly, the sustaining structure supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps device to stop stress on the tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of removing the existing taps can be fairly bothersome because of the limited gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will come from the pipelines. When the supply pipes have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before carrying on to fit the new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Using both wood boards under its feet, place the bathtub in the needed setting. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four small factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bath tub until the level reviews level.
To install taps, fit all-time low of the furthest adaptable tap port to the proper supply pipe by making a compression join; then do the same for the various other faucet.
Activate the supply of water and also inspect all joints and also new pipework for leakages and also tighten them if necessary. Fill the bath tub and also inspect the overflow electrical outlet and the regular outlet for leakages.
Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling as well as sealing around the bath tub must wait up until the tub has actually been used a minimum of when as this will certainly settle it into its final placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in location between the faucet as well as the sink. Protect the faucet in position with the maker provided backnut. As soon as the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet connectors. The former kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall between the bathroom as well as the tiling, causing difficulties with wetness and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in use. The sealer can split fairly very early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on Installing A Bathtub, I was thinking sharing that excerpt was essential. Remember to take the time to share this page if you enjoyed reading it. We take joy in reading our article about How to Install a Bathtub Yourself.
Plumbing integrity assured. Report this page